Power Management ICs

ACS758-KCB150B Hall-Effect-Based Linear Current Sensor IC provides economical and precise solutions for AC or DC current sensing. Typical applications include motor control, load detection and management, power supply and DC-to-DC converter control, inverter control, and overcurrent fault detection

1Amp 1000V Bridge Rectifier IC is good for automation insertion surge overload rating. 1-ampere IC rectifier is ideal for printed circuit board reliable low-cost construction utilizing molded glass passivated device Polarity symbols molded on body Mounting position. This IC rectifier chip leads solderable per MIL-STD-202 and method 208 guaranteed.

This is SOP8 To DIP8  200mil IC Test and Burn-In Socket. It applies to all the chips of SOP8 that have a wide body. This chip prog socket is brand new and high quality. It is RoHS compliant.

24c04 SMD EEPROM in Pakistan

This is a Bipolar PNP transistor available in a metal can package, having a high value of current 600mA with a low voltage of 40v. The condition of being forward biased is when the base is connected to the ground or has no supply on it, and as a signal is provided to the base pin it goes reverse-biased. The transistor is having DC current gain value of 100 to 300 which shows the amplification capacity of the transistor. As it is used for amplification and switching.

2N2222A Bipolar Junction NPN Transistor is commonly used in general-purpose low-power amplifying/switching applications. Bipolar Junction NPN Transistor is designed for low to medium current, low power, and medium voltage, and can operate at moderately high speeds. It was originally made in the TO-18 metal can as shown in the picture. We have many other NPN transistors like BD139, BC547, BC548, 2SC945, etc.

2Sd1047 NPN POWER TRANSISTOR In Pakistan

The 555 is a highly stable device for generating accurate time delays or oscillations. Additional terminals are provided for triggering or resetting if desired. In the time delay mode of operation, the time is precisely controlled by one external resistor and capacitor. For astable operation as an oscillator, the free running frequency and duty cycle are accurately controlled with two external resistors and one capacitor. The circuit may be triggered and reset on falling waveforms, and the output circuit can source or sink up to 200mA or drive TTL circuits.

5V Voltage Regulator SMD IC Chip 78M05, voltage sources in a circuit may have fluctuations resulting in not providing fixed voltage outputs. A voltage regulator IC maintains the output voltage at a constant value. 7805 IC, a member of the 78xx series of fixed linear voltage regulators used to maintain such fluctuations, is a popular voltage regulator integrated circuit (IC). The xx in 78xx indicates the output voltage it provides. 7805 IC chip provides +5 volts regulated power supply with provisions to add a heat sink.

IC, EL 6N137, Optocoupler, DIP8. It is single-channel and it consists of an 850 nm AlGaAS LED, optically coupled to a very high-speed integrated photo-detector logic gate with a strobe output. This output features an open collector, thereby permitting wired OR outputs.

The device includes an on-chip Hall voltage generator for magnetic sensing, a comparator that amplifies the Hall voltage, and a Schmitt trigger to provide switching hysteresis for noise rejection, and open-collector output. An internal bandgap regulator is used to provide temperature compensated supply voltage for internal circuits and allows a wide operating supply range.

The ADC0804 is a commonly used ADC module, for projects where an external ADC is required. It is a 20-pin Single channel 8-bit ADC module. Meaning it can measure one ADC value from 0V to 5V and the precision when voltage reference (Vref –pin 9) is +5V is 19.53mV (Step size). That is for every increase of 19.53mV on the input side there will be an increase of 1 bit on the output side.

This IC is very Ideal to use with Microprocessors like Raspberry Pi, Beagle bone, etc. Or even to use as a standalone ADC module. Every ADC module requires a clock to function; this IC comes with its own internal clock so you don’t have to worry about it. Hence, if you are looking for a compact ADC module with a decent resolution of 8-bit then this IC is for you.

The Voltage Regulator LM317 device is an adjustable three-terminal positive-voltage regulator. This adjustable volt regulator is capable of supplying more than 1.5 A over an output-voltage range of 1.25 V to 37 V. This LM 317 regulator requires only two external resistors to set the output voltage. The device features a typical line regulation of 0.01% and a typical load regulation of 0.1%.

The AM26LS32Ax and AM26LS33Ax devices are quadruple differential line receivers for balanced and unbalanced digital data transmission. The enable function is common to all four receivers and offers a choice of active-high or active-low input. The 3-state outputs permit connection directly to a bus-organized system. Fail-safe design ensures that, if the inputs are open, the outputs always are high. Compared to the AM26LS32 and the AM26LS33, the AM26LS32A, and AM26LS33A incorporate an additional stage of amplification to improve sensitivity. The input impedance has been increased, resulting in less loading of the bus line. The additional stage has increased propagation delay; however, this does not affect interchangeability in most applications. The AM26LS32AC and AM26LS33AC are characterized for operation from 0°C to 70°C.