- Raspberry Pi & Accessories
- Raspberry Pi Kits
- Raspberry Pi Board
- Raspberry Pi Case
- Raspberry Pi Came
- Raspberry Pi Accessories
New CNC Router Single Axis 3A TB6560 Stepper Motor Drivers Board For Axis Control. Very easy to use, no instructions, all of us are marked on the board. A large heat sink to ensure good heat dissipation. Input signal high-speed optocoupler isolation, guarantee not losing steps. Semi-flow mode adjustable, semi-flow current adjustable, not the general design on the market, with a variety of semi-flow models and semi-flow current setting functions. The attenuation model adjusted for all the motors can be locked when no noise.
Working voltage: DC 10V-35V.Recommend Switching Power Supply DC24V
- 6N137 high-speed OptoCoupler, to ensure a high speed without stepping out.
- New original Toshiba TB6560AHQ chip, low-voltage shutdown, overheating parking, and over-current protection circuit to ensure optimal performance.
- Rated output: ± 3A, peak 3.5A.
- For 42,57,86 Stepper within 3A 2/4 -phase / 4 wire / 6 wire stepper motor, not fit for more than 3A stepper motor.
- Automatic half-decay.
- Excitation Mode: synchronizing, half step, 1/8 step, 1/16 step, a maximum of 16 segments.
- Volume: 50 x 75 x 35 ( MM)
Package Includes:
- 1 x TB6560 Single Axis 3A Stepper Motor Driver In Pakistan
Add a review
You must be logged in to post a review
Log In
Related products
- Stepper Motor
TB6600 Stepper Motor Driver Control Board Module In Pakistan
TB6600 Arduino Stepper Motor Driver is an easy-to-use professional stepper motor driver, which could control a two-phase stepping motor. It is compatible with Arduino and other microcontrollers that can output a 5V digital pulse signal. TB6600 Arduino stepper motor driver has a wide range of power input, 9~42VDC power supply. And it is able to output 4A peak current, which is enough for most stepper motors. The stepper driver supports speed and direction control. You can set its micro-step and output current with 6 DIP switches. There are 7 kinds of micro-steps (1, 2 / A, 2 / B, 4, 8, 16, 32) and 8 kinds of current control (0.5A, 1A, 1.5A, 2A, 2.5A, 2.8A, 3.0A, 3.5A) in all. And all signal terminals adopt high-speed optocoupler isolation, enhancing their anti-high-frequency interference ability. As a professional device, it is able to drive 57, 42-type two-phase, four-phase, hybrid stepper motor.
SKU: D398 - Stepper Motor
DRV8825 Stepper Motor Driver Module For Arduino In Pakistan
The DRV8825 Stepper Motor Driver with Aluminum Heat Sink is a breakout board for TI’s DRV8825 micro-stepping bipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of the A4988 stepper motor driver carriers, so it can be used as a higher-performance drop-in replacement for those boards in many applications. The DRV8825 features adjustable current limiting, overcurrent, and overtemperature protection, and six micro step resolutions (down to 1/32-step). It operates from 8.2 – 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling).
SKU: D400 - Stepper Motor
L293D Motor Driver Shield Expansion Board For Arduino In Pakistan
The L293D Motor Driver/Servo Shield for Arduino is probably one of the most versatile on the market and features 2 servo and 4 motor connectors for DC or stepper motors. That makes it a great shield for any robotic project. This Arduino compatible motor Driver shield is a full-featured product that it can be used to drive 4 DC motors or two 4-wire steppers and two 5v servos. It drives the DC motor and stepper with the L293D, and it drives the servo with Arduino pin9 and pin10. The shield contains two L293D motor drivers and one 74HC595 shift register. The shift register expands 3 pins of the Arduino to 8 pins to control the direction of the motor drivers. The output enables the L293D is directly connected to the PWM outputs of the Arduino.
SKU: D388,B75
Reviews
There are no reviews yet