LM741 Operational Amplifier In Pakistan
The LM741 series are general-purpose operational amplifiers that feature improved performance over industry standards like the LM709. This high-speed op-amp LM-741 is a direct, plug-in replacement for the 709C, LM201, MC1439, and 748 in most applications. The operational amplifiers offer many features which make their application nearly foolproof: overload protection on the input and output, no latch-up when the common-mode range is exceeded, as well as freedom from oscillations. The LM741C op-amp amplifier is identical to the LM741 and LM741A except that the LM741C has their performance ensured over a 0°C to +70°C temperature range, instead of −55°C to +125°C.
₨28
The LM741 series are general-purpose operational amplifiers that feature improved performance over industry standards like the LM709. This high-speed op-amp LM-741 is a direct, plug-in replacement for the 709C, LM201, MC1439, and 748 in most applications. The operational amplifiers offer many features which make their application nearly foolproof: overload protection on the input and output, no latch-up when the common-mode range is exceeded, as well as freedom from oscillations. The LM741C op-amp amplifier is identical to the LM741 and LM741A except that the LM741C has their performance ensured over a 0°C to +70°C temperature range, instead of −55°C to +125°C.
Features Of LM741 Op-amp IC:
- LM741 has only one op-amp inside, there are some op-amp IC’s having more than one op-amp like LM358, LM148, LM248, LM348.
- Provided short circuit and overload protection.
- Low power consumption.
- Large common-mode rejection ratio (CMRR) and differential voltage ranges.
- No external frequency compensation is required.
- Prevent latch-up when the common-mode range is exceeded.
- The minimum, normal, and maximum Power Consumption for this IC is ±10v, ±15v and ±22v respectively.
- The operating temperature should be -50 to 125 ˚C.
- Supply current – 1.7 to 2.8mA.
- Soldering pin temperature – PDIP package – 260 ˚C (for 10 seconds – prescribed).
- TO-99 and CDIP – 300 ˚C (for 10 seconds – prescribed).
Specifications Of LM-741 Operational Amplifier:
- Number of Channels (#): 1
- Total Supply Voltage (Min) (+5V=5, +/-5V=10): 10
- Total Supply Voltage (Max) (+5V=5, +/-5V=10): 44
- GBW (Typ) (MHz): 1
- Slew Rate (Typ) (V/us): 0.5
- Vos (Offset Voltage @ 25C) (Max) (mV): 3
- Iq per channel (Typ) (mA): 1.7
- Rating: Catalog
- Operating Temperature Range (C): -40 to 85^-55 to 125^0 to 70
- Package Group: CDIP^PDIP^TO-99^WAFERSALE
- Output Current (Typ) (mA): 25
- Offset Drift (Typ) (uV/C): 15
- Vn at 1kHz (Typ) (nV/rtHz): 30
- Architecture: Bipolar
- Additional Features: N/A
- IIB (Max) (pA): 80000
- CMRR (Typ) (dB): 90
Package Includes:
- 1 x Operational Amplifier LM741
Related products
- Power Management ICs
ULN2803 ULN2803A ULN2803APG IC In Pakistan
The ULN2803A is a high-voltage, high-current Darlington transistor array. The device consists of eight NPN Darlington pairs that feature high-voltage outputs with common-cathode clamp diodes for switching inductive loads. The collector-current rating of each Darlington pair is 500 mA. The Darlington pairs may be connected in parallel for higher current capability. Applications include relay drivers, hammer drivers, lamp drivers, display drivers (LED and gas discharge), line drivers, and logic buffers. The ULN2803A has a 2.7-k series base resistor for each Darlington pair for operation directly with TTL or 5-V CMOS devices
SKU: D2083 - Power Management ICs
L293D IC Dual H-Bridge Motor Driver In Pakistan
The Device is a monolithic integrated high voltage, high current four channel driver designed to accept standard DTL or TTL logic levels and drive inductive loads (such as relays solenoids, DC, and stepping motors) and switching power transistors. To simplify use as two bridges each pair of channels is equipped with an enable input. A separate supply input is provided for the logic, allowing operation at a lower voltage, and internal clamp diodes are included. This device is suitable for use in switching applications at frequencies up to 5 kHz. The L293D is assembled in a 16-lead plastic package that has 4 center pins connected together and used for heatsinking.
SKU: D2084 - Power Management ICs
LM7805 L7805 7805 Linear Voltage Regulator IC In Pakistan
The LM7805CV is a fixed output, three-terminal precision positive voltage regulator in 3 pins TO-220 package. This regulator can provide local on-card regulation by eliminating distribution problems associated with single-point regulation. The L7805 fixed voltage regulator is designed with thermal overload protection that shuts down the circuit when subjected to an excessive power overload condition, internal short circuit protection that limits the maximum current the circuit will pass, and output transistor safe area compensation that reduces the output short circuit as the voltage across the pass transistor is increased. If adequate heat sinking is provided then this positive voltage regulator can deliver over 1A output current.
SKU: D1190 - Power Management ICs
DIP-8 gate drivers ic chip IR2104 in Pakistan
Fully operational to +600V Tolerant to negative transient voltage dV/dt immune Gate drive supply range from to 20V Undervoltage lockout 3.3V, 5V and 15V input logic compatible Cross-conduction prevention logic Internally set deadtime High side output in phase with input Shut down input turns off both channels Matched propagation delay for both channels
SKU: D2085 - Power Management ICs
TL431 TL431A 431 Voltage Regulator IC In Pakistan
The TL431 is a three-terminal adjustable precision shunt voltage regulator integrated circuit. With the use of an external voltage divider, a TL431 can regulate voltages ranging from 2.5 to 36 V, at currents up 100 mA. The typical initial deviation of reference voltage from the nominal 2.495 V level is measured in millivolts, the maximum worst-case deviation is measured in tens of millivolts.
SKU: D1203
Reviews
There are no reviews yet