- Raspberry Pi & Accessories
- Raspberry Pi Kits
- Raspberry Pi Board
- Raspberry Pi Case
- Raspberry Pi Came
- Raspberry Pi Accessories
This is a simple water sensor, that can be used to detect soil moisture Module Output is a high level when the soil moisture deficit or output is low Can be used in a module plant waterer device, and the plants in your garden not need people to manage
Specification:
- Operating voltage: 3.3V~5V
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having an LM393 comparator chip, stable
- Panel PCB Dimension: Approx.3cm x 1.5cm
- Soil Probe Dimension: Approx. 6cm x 3cm
- Cable Length: Approx.21cm
- Interface Description(4-wire):
- VCC: 3.3V-5V
- GND: GND
- DO: digital output interface(0 and 1)
- AO: analog output interface
Package includes:
- 1x Soil Moisture Sensor For Arduino in Pakistan
Add a review
You must be logged in to post a review
Log In
Related products
- Arduino Sensor And Modules
MQ3 Alcohol Ethanol Detector Gas Sensor Module in Pakistan
MQ3 MQ 3 MQ-3 Alcohol Detector Gas Sensor Module is a simple to use MQ-3 Alcohol Detector Gas Sensor Module which can sense the presence of Alcohol in the air. The module uses our MQ-3 sensor. It simplifies the interface to the odd pin spacing of the sensor and provides an interface through standard 4 x 0.1″ header pins. It provides an analog output corresponding to the concentration of the gas in the air and an easy-to-use digital output. The onboard potentiometer can be used to set the maximum gas concentration beyond which the digital output gets triggered. Just power the module with 5V set the threshold and you can start getting the gas concentration of the air around the sensor! An onboard LED signals the presence of any gas. Perfect sensing alcohol concentration on your breath just likes a common breathalyzer. The digital output can be easily interfaced with microcontrollers and other circuits. The analog output can be hooked up to an ADC of a microcontroller to get a wide range of sensor readings.
SKU: D56,B105 - Arduino Sensor And Modules
MQ7 CO Carbon Monoxide Coal Gas Sensor Module In Pakistan
MQ7 MQ 7 MQ-7 CO Carbon Monoxide Coal Gas Sensor Module For Arduino detects the concentrations of CO in the air and outputs its reading as an analog voltage. The sensor can measure concentrations of 10 to 10,000 ppm. The sensor can operate at temperatures from -10 to 50°C and consumes less than 150 mA at 5 V.This module provides both digital and analog outputs. The threshold level for digital output can be easily adjusted using the preset on the board. The MQ-7 sensor module can be easily interfaced with microcontrollers, Arduino, etc.
SKU: D52,B105 - Arduino Sensor And Modules
MQ9 Carbon Monoxide Methane And LPG Gas Sensor Module in Pakistan
Quick View
Arduino Sensor And ModulesMQ9 Carbon Monoxide Methane And LPG Gas Sensor Module in Pakistan
MQ9 MQ 9 MQ-9 Carbon Monoxide, Methane, and LPG Gas Sensor Module For Arduino can be used to sense Carbon Monoxide and Methane Gas. The sensitive material of the MQ9 MQ 9 MQ-9 gas sensor is SnO2, which with lower conductivity in clean air. It makes detection by method of cycle high and low temperature, and detect CO when low temperature (heated by 1.5V). The sensor’s conductivity is higher along with the gas concentration rising. When the high temperature (heated by 5.0V), detects Methane, Propane, etc. combustible gas and cleans the other gases adsorbed under low temperature.
SKU: D50,B105 - Arduino Sensor And Modules
MAX9814 Microphone Amplifier Module In Pakistan
The MAX9814 is available in the space-saving, 14-pin TDFN package. This device is specified over the -40°C to +85°C extended temperature range. MAX9814 is a low-cost, high-quality microphone amplifier with automatic gain control (AGC) and low-noise microphone bias. The device features a low-noise preamplifier, variable gain amplifier (VGA), output amplifier, microphone-bias-voltage generator, and AGC control circuitry. The low-noise preamplifier has a fixed 12dB gain, while the VGA gain automatically adjusts from 20dB to 0dB, depending on the output voltage and the AGC threshold. The output amplifier offers selectable gains of 8dB, 18dB, and 28dB. With no compression, the cascade of the amplifiers results in an overall gain of 40dB, 50dB, or 60dB. A trilevel digital input programs the output amplifier gain. An external resistive divider controls the AGC threshold and a single capacitor programs the attack/release times. A trilevel digital input programs the ratio of attack-to-release time. The hold time of the AGC is fixed at 30ms. The low-noise microphone-bias-voltage generator can bias most electret microphones.
SKU: D64,SB47 - Arduino Sensor And Modules
MQ2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module in Pakistan
Quick View
Arduino Sensor And ModulesMQ2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module in Pakistan
MQ2 MQ-2 MQ 2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module Smoke LPG Butane Hydrogen Gas Sensor Detector Module is useful for gas leakage detection (home and industry). It is suitable for detecting H2, LPG, CH4, CO, Alcohol, Smoke, or Propane. Due to its high sensitivity and fast response time, the measurement can be taken as soon as possible. The sensitivity of the sensor can be adjusted by a potentiometer.MQ-2 gas sensor using gas sensitive material is to be clean air in the lower conductivity of tin oxide (SnO2). When the sensor when flammable gases are present in the environment in which the sensor’s conductivity with increasing concentration of combustible gas in the air increases. Use a simple circuit to convert the changes in conductivity and output signal that corresponds to the concentration of the gas.MQ-2 gas sensor higher sensitivity to liquefied petroleum gas, propane, hydrogen, detection of gas, and other combustible vapors are ideal. This sensor can detect a variety of flammable gas, are a low-cost sensor for many applications.
SKU: D57,B105
Reviews
There are no reviews yet