- Raspberry Pi & Accessories
- Raspberry Pi Kits
- Raspberry Pi Board
- Raspberry Pi Case
- Raspberry Pi Came
- Raspberry Pi Accessories
Arduino Sensor And Modules
Compare
KY 020 KY-020 Tilt Switch Sensor Module for Arduino In Pakistan
KY-020 Arduino tilt switch sensor module. Closes the circuit when it is tilted to the side as long as it is moved with enough force and degree of inclination to activate the ball switch inside.
₨150
The KY-020 consists of a 10kΩ resistor and a metallic ball switch with bidirectional conduction that will open/close the circuit depending on its tilt degree. It does not measure tilt angle.
Specification of KY-020 Tilt Switch Sensor Module for Arduino:
- Model Number: KY-020
- Product Name: Tilt Switch Sensor
- Operating Voltage:3.3V to 5v
- Output Type: Digital
- Size / Dimension:18*15mm
Package Include:
- 1 x KY-020 Tilt Switch Sensor Module for Arduino In Pakistan
Add a review
You must be logged in to post a review
Log In
Related products
- Arduino Sensor And Modules
AD8232 Keyes Single Lead ECG Monitoring Sensor Module In Pakistan
Quick View
Arduino Sensor And ModulesAD8232 Keyes Single Lead ECG Monitoring Sensor Module In Pakistan
The AD8232 Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG or Electrocardiogram and output as an analog reading. ECGs can be extremely noisy, the AD8232 Single Lead Heart Rate Monitor acts as an op-amp to help obtain a clear signal from the PR and QT Intervals easily. The AD8232 is an integrated signal conditioning block for ECG and other bio-potential measurement applications. It is designed to extract, amplify, and filter small bio-potential signals in the presence of noisy conditions, such as those created by motion or remote electrode placement.
SKU: D42,B104 - Arduino Sensor And Modules
MQ6 Liquefied Petroleum Isobutane Propane LPG Gas Sensor Module In Pakistan
Quick ViewArduino Sensor And ModulesMQ6 Liquefied Petroleum Isobutane Propane LPG Gas Sensor Module In Pakistan
MQ6 MQ 6 MQ-6 Liquefied Petroleum isobutane-propane gas Sensor Module For Arduino. This sensor has high sensitivity and fast response time. The sensor’s output is an analog resistance. The drive circuit is very simple; all you need to do is power the heater coil with 5V, add a load resistance, and connect the output to an ADC. The sensitive material of the MQ-6 gas sensor is SnO2, which with lower conductivity in clean air. When the target combustible gas exists, The sensor’s conductivity is higher along with the gas concentration rising. Please use a simple electro circuit, Convert the change of conductivity to correspond output signal of gas concentration.MQ-6 gas sensor has a high sensitivity to Propane, Butane, and LPG, also a response to Natural gas. The sensor could be used to detect different combustible gas, especially Methane, which is with low cost and suitable for different applications.
SKU: D53,B105 - Arduino Sensor And Modules
Arduino Voice Recognition Module V3 In Pakistan
Speak (Voice) Recognition Module V3 -Arduino Compatible is a compact and easy-control speaking recognition board In Pakistan.Speak (Voice) Recognition Module V3 product is a speaker-dependent voice recognition module. It supports up to 80 voice commands in all. Max 7 voice commands could work at the same time. Any sound could be trained as the command. Users need to train the module first before let it recognizing any voice command. This board has 2 controlling ways: Serial Port (full function), General Input Pins (part of a function). General Output Pins on the board could generate several kinds of waves while corresponding voice command was recognized.
SKU: D63 - Arduino Sensor And Modules
MQ3 Alcohol Ethanol Detector Gas Sensor Module in Pakistan
MQ3 MQ 3 MQ-3 Alcohol Detector Gas Sensor Module is a simple to use MQ-3 Alcohol Detector Gas Sensor Module which can sense the presence of Alcohol in the air. The module uses our MQ-3 sensor. It simplifies the interface to the odd pin spacing of the sensor and provides an interface through standard 4 x 0.1″ header pins. It provides an analog output corresponding to the concentration of the gas in the air and an easy-to-use digital output. The onboard potentiometer can be used to set the maximum gas concentration beyond which the digital output gets triggered. Just power the module with 5V set the threshold and you can start getting the gas concentration of the air around the sensor! An onboard LED signals the presence of any gas. Perfect sensing alcohol concentration on your breath just likes a common breathalyzer. The digital output can be easily interfaced with microcontrollers and other circuits. The analog output can be hooked up to an ADC of a microcontroller to get a wide range of sensor readings.
SKU: D56,B105 - Arduino Sensor And Modules
Fingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
Quick ViewArduino Sensor And ModulesFingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
The GT511C3 GT-511C3 GT 511C3 FPS (fingerprint scanner) is a small embedded module that consists of an optical sensor mounted on a small circuit board. The optical sensor scans a fingerprint and the microcontroller and software provide the functionality of the module which automatically processes the scanned fingerprint. The GT511C3 GT-511C3 GT 511C3 Optical Fingerprint Scanner Module with JST SH Connector is a high-performance fingerprint scanner. This optical sensor module is designed for easy integration into applications with a serial interface (UART). The GT-511C3 is a TTL fingerprint scanner and can be accessed by Raspberry Pi, Arduino, or any other Microcontroller using just two wires viz Tx & Rx.GT-511C3 Fingerprint Scanner module has an onboard optical sensor and a 32-bit CPU. It does most of the heavy work like reading and identifying fingerprints. A simple set of commands has to be sent from your micro-controller and the GT-511C3 fingerprint scanner does the rest of the work. To get started, just register each fingerprint that you want to store by sending the corresponding command and pressing your finger against the reader three times. The fingerprint scanner can store different fingerprints and the database of prints can even be downloaded from the unit and distributed to other modules. As well as the fingerprint “template,” the analyzed version of the print, you can also retrieve the image of a fingerprint and even pull raw images from the optical sensor. We need two wires are for TX and RX and two wires for the power supply (5V). The module can be used in projects for identifying users, for example allowing access through a door by scanning a finger instead of using a key.
SKU: D46
Reviews
There are no reviews yet