- Raspberry Pi & Accessories
- Raspberry Pi Kits
- Raspberry Pi Board
- Raspberry Pi Case
- Raspberry Pi Came
- Raspberry Pi Accessories
Arduino Sensor And Modules
Compare
KY 018 KY-018 Photosensitive Resistor Module Light Detection LDR Sensor Module for Arduino In Pakistan
Arduino KY018 KY 018 KY-018 Photoresistor module, used to measure light intensity. It can determine the presence or absence of light.
₨100
This module consists of a photoresistor and a 10 kΩ in-line resistor. The photoresistor’s resistance will decrease in the presence of light and increase in the absence of it. The output is analog and determines the intensity of light.
Specification of Ky-018 Photosensitive Resistor Module Light Detection LDR Sensor Module for Arduino:
- Model: KY-018
- Product Name: LDR Light Detection Sensor Module
- Operating Voltage:3.3V to 5V
- Output type: Analog
Package Include:
- 1 x KY-018 Photosensitive Resistor Module Light Detection LDR Sensor Module for Arduino In Pakistan
Add a review
You must be logged in to post a review
Log In
Related products
- Arduino Sensor And Modules
Fingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
Quick View
Arduino Sensor And ModulesFingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
The GT511C3 GT-511C3 GT 511C3 FPS (fingerprint scanner) is a small embedded module that consists of an optical sensor mounted on a small circuit board. The optical sensor scans a fingerprint and the microcontroller and software provide the functionality of the module which automatically processes the scanned fingerprint. The GT511C3 GT-511C3 GT 511C3 Optical Fingerprint Scanner Module with JST SH Connector is a high-performance fingerprint scanner. This optical sensor module is designed for easy integration into applications with a serial interface (UART). The GT-511C3 is a TTL fingerprint scanner and can be accessed by Raspberry Pi, Arduino, or any other Microcontroller using just two wires viz Tx & Rx.GT-511C3 Fingerprint Scanner module has an onboard optical sensor and a 32-bit CPU. It does most of the heavy work like reading and identifying fingerprints. A simple set of commands has to be sent from your micro-controller and the GT-511C3 fingerprint scanner does the rest of the work. To get started, just register each fingerprint that you want to store by sending the corresponding command and pressing your finger against the reader three times. The fingerprint scanner can store different fingerprints and the database of prints can even be downloaded from the unit and distributed to other modules. As well as the fingerprint “template,” the analyzed version of the print, you can also retrieve the image of a fingerprint and even pull raw images from the optical sensor. We need two wires are for TX and RX and two wires for the power supply (5V). The module can be used in projects for identifying users, for example allowing access through a door by scanning a finger instead of using a key.
SKU: D46 - Arduino Sensor And Modules
MQ8 Hydrogen Gas Sensor Module in Pakistan
MQ8 MQ 8 MQ-8 Hydrogen Gas Sensor Module For Arduino H2 Alarm Detection MQ-8 Sensor Hydrogen Gas Sensor Module H2 Alarm Detection use in clean air low conductivity tin oxide (SnO2). When there is an environment in which the combustible gas sensor, conductivity sensor with increasing concentration of combustible gases in air increases. Using a simple circuit to convert the change in conductivity of the gas concentration corresponding to the output signal. MQ-8 hydrogen gas sensor of high sensitivity, the monitoring of the other hydrogen-containing gas is also very satisfactory. This sensor can detect a wide range of hydrogen gas, city gas, in particular, is a low-cost sensor for a variety of applications.
SKU: D51,B105 - Arduino Sensor And Modules
MQ2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module in Pakistan
Quick ViewArduino Sensor And ModulesMQ2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module in Pakistan
MQ2 MQ-2 MQ 2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module Smoke LPG Butane Hydrogen Gas Sensor Detector Module is useful for gas leakage detection (home and industry). It is suitable for detecting H2, LPG, CH4, CO, Alcohol, Smoke, or Propane. Due to its high sensitivity and fast response time, the measurement can be taken as soon as possible. The sensitivity of the sensor can be adjusted by a potentiometer.MQ-2 gas sensor using gas sensitive material is to be clean air in the lower conductivity of tin oxide (SnO2). When the sensor when flammable gases are present in the environment in which the sensor’s conductivity with increasing concentration of combustible gas in the air increases. Use a simple circuit to convert the changes in conductivity and output signal that corresponds to the concentration of the gas.MQ-2 gas sensor higher sensitivity to liquefied petroleum gas, propane, hydrogen, detection of gas, and other combustible vapors are ideal. This sensor can detect a variety of flammable gas, are a low-cost sensor for many applications.
SKU: D57,B105 - Arduino Sensor And Modules
MQ7 CO Carbon Monoxide Coal Gas Sensor Module In Pakistan
MQ7 MQ 7 MQ-7 CO Carbon Monoxide Coal Gas Sensor Module For Arduino detects the concentrations of CO in the air and outputs its reading as an analog voltage. The sensor can measure concentrations of 10 to 10,000 ppm. The sensor can operate at temperatures from -10 to 50°C and consumes less than 150 mA at 5 V.This module provides both digital and analog outputs. The threshold level for digital output can be easily adjusted using the preset on the board. The MQ-7 sensor module can be easily interfaced with microcontrollers, Arduino, etc.
SKU: D52,B105 - Arduino Sensor And Modules
MQ3 Alcohol Ethanol Detector Gas Sensor Module in Pakistan
MQ3 MQ 3 MQ-3 Alcohol Detector Gas Sensor Module is a simple to use MQ-3 Alcohol Detector Gas Sensor Module which can sense the presence of Alcohol in the air. The module uses our MQ-3 sensor. It simplifies the interface to the odd pin spacing of the sensor and provides an interface through standard 4 x 0.1″ header pins. It provides an analog output corresponding to the concentration of the gas in the air and an easy-to-use digital output. The onboard potentiometer can be used to set the maximum gas concentration beyond which the digital output gets triggered. Just power the module with 5V set the threshold and you can start getting the gas concentration of the air around the sensor! An onboard LED signals the presence of any gas. Perfect sensing alcohol concentration on your breath just likes a common breathalyzer. The digital output can be easily interfaced with microcontrollers and other circuits. The analog output can be hooked up to an ADC of a microcontroller to get a wide range of sensor readings.
SKU: D56,B105
Reviews
There are no reviews yet