- Raspberry Pi & Accessories
- Raspberry Pi Kits
- Raspberry Pi Board
- Raspberry Pi Case
- Raspberry Pi Came
- Raspberry Pi Accessories
Arduino Sensor And Modules
Compare
KY 011 KY-011 Two Color Red and Green LED Common Cathode Sensor Module In Pakistan
This module consists of a common cathode 5mm Red/Green LED and a 0Ω resistor, Since the operating voltage is 2.0v ~2.5v you’ll need to use limiting resistors to prevent burnout when connecting to the Arduino.
₨80
Specification of KY-011 Two Color Red and Green LED Common Cathode Sensor Module:
- Color: Green + Red
- Diameter: 5mm
- Package-Type: Diffusion
- Voltage: 2.0-2.5v
- Current: 10mA
- Viewing angle: 150 degree
- Wavelength: 571 +644 nm
- Luminous intensity (MCD):20-40; 40-80
- Stent type: long-legged
Package Include:
- 1 x KY-011 Two Color Red and Green LED Common Cathode Sensor Module In Pakistan
Add a review
You must be logged in to post a review
Log In
Related products
- Arduino Sensor And Modules
MQ9 Carbon Monoxide Methane And LPG Gas Sensor Module in Pakistan
Quick View
Arduino Sensor And ModulesMQ9 Carbon Monoxide Methane And LPG Gas Sensor Module in Pakistan
MQ9 MQ 9 MQ-9 Carbon Monoxide, Methane, and LPG Gas Sensor Module For Arduino can be used to sense Carbon Monoxide and Methane Gas. The sensitive material of the MQ9 MQ 9 MQ-9 gas sensor is SnO2, which with lower conductivity in clean air. It makes detection by method of cycle high and low temperature, and detect CO when low temperature (heated by 1.5V). The sensor’s conductivity is higher along with the gas concentration rising. When the high temperature (heated by 5.0V), detects Methane, Propane, etc. combustible gas and cleans the other gases adsorbed under low temperature.
SKU: D50,B105 - Arduino Sensor And Modules
ECG Electrodes with Metal Snap and Low Impedance Solid Medical Conductive Gel In Pakistan
Quick ViewArduino Sensor And ModulesECG Electrodes with Metal Snap and Low Impedance Solid Medical Conductive Gel In Pakistan
ECG Electrodes with Metal Snap and Low Impedance Solid Medical Conductive Gel Disposable ECG electrodes are used for diagnostic ECG or ECG monitoring They can be used for various ECG tests Chunfeng and reg; Disposable ECG electrodes use an AG/AgClsensor element and solid conductive and adhesive Hydro-gel for adhesion The AG/AgCl sensor element has the best sensitivities and the solid conductive and adhesive hydro-gel has very low impedance and is non-irritating, non-sensitizing and non-cytotoxic to the skin All electrodes are latex-free.
SKU: D41,B104 - Arduino Sensor And Modules
MQ3 Alcohol Ethanol Detector Gas Sensor Module in Pakistan
MQ3 MQ 3 MQ-3 Alcohol Detector Gas Sensor Module is a simple to use MQ-3 Alcohol Detector Gas Sensor Module which can sense the presence of Alcohol in the air. The module uses our MQ-3 sensor. It simplifies the interface to the odd pin spacing of the sensor and provides an interface through standard 4 x 0.1″ header pins. It provides an analog output corresponding to the concentration of the gas in the air and an easy-to-use digital output. The onboard potentiometer can be used to set the maximum gas concentration beyond which the digital output gets triggered. Just power the module with 5V set the threshold and you can start getting the gas concentration of the air around the sensor! An onboard LED signals the presence of any gas. Perfect sensing alcohol concentration on your breath just likes a common breathalyzer. The digital output can be easily interfaced with microcontrollers and other circuits. The analog output can be hooked up to an ADC of a microcontroller to get a wide range of sensor readings.
SKU: D56,B105 - Arduino Sensor And Modules
MAX30102 SPO2 Blood Oxygen Pulse Oximeter and Heart Rate Sensor In Pakistan
Quick ViewArduino Sensor And ModulesMAX30102 SPO2 Blood Oxygen Pulse Oximeter and Heart Rate Sensor In Pakistan
The MAX30102 is an integrated pulse oximeter or SO2 sensors, and heart rate monitor biosensor module. MAX30102 SO2 integrates a red LED and an infrared LED, photodetector, optical components, and low-noise electronic circuitry with ambient light suppression.
SKU: D43 - Arduino Sensor And Modules
Fingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
Quick ViewArduino Sensor And ModulesFingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
The GT511C3 GT-511C3 GT 511C3 FPS (fingerprint scanner) is a small embedded module that consists of an optical sensor mounted on a small circuit board. The optical sensor scans a fingerprint and the microcontroller and software provide the functionality of the module which automatically processes the scanned fingerprint. The GT511C3 GT-511C3 GT 511C3 Optical Fingerprint Scanner Module with JST SH Connector is a high-performance fingerprint scanner. This optical sensor module is designed for easy integration into applications with a serial interface (UART). The GT-511C3 is a TTL fingerprint scanner and can be accessed by Raspberry Pi, Arduino, or any other Microcontroller using just two wires viz Tx & Rx.GT-511C3 Fingerprint Scanner module has an onboard optical sensor and a 32-bit CPU. It does most of the heavy work like reading and identifying fingerprints. A simple set of commands has to be sent from your micro-controller and the GT-511C3 fingerprint scanner does the rest of the work. To get started, just register each fingerprint that you want to store by sending the corresponding command and pressing your finger against the reader three times. The fingerprint scanner can store different fingerprints and the database of prints can even be downloaded from the unit and distributed to other modules. As well as the fingerprint “template,” the analyzed version of the print, you can also retrieve the image of a fingerprint and even pull raw images from the optical sensor. We need two wires are for TX and RX and two wires for the power supply (5V). The module can be used in projects for identifying users, for example allowing access through a door by scanning a finger instead of using a key.
SKU: D46
Reviews
There are no reviews yet