- Raspberry Pi & Accessories
- Raspberry Pi Kits
- Raspberry Pi Board
- Raspberry Pi Case
- Raspberry Pi Came
- Raspberry Pi Accessories
Infrared Remote for Arduino is available in Pakistan. The technology implemented is infrared (IR) light. The signal between a remote control handset and the device it controls consists of pulses of infrared light, and the signal can be seen by a digital camera, video camera, or phone camera.
Package Includes :
- 1 x Arduino Infrared Remote in Pakistan
Add a review
You must be logged in to post a review
Log In
Related products
- Arduino Sensor And Modules
Voice Recognition Module With Microphone Control Voice Board For Arduino in Pakistan
Quick View
Arduino Sensor And ModulesVoice Recognition Module With Microphone Control Voice Board For Arduino in Pakistan
This Voice Recognition Module, which can recognize as many as 15 voice instructions and be suitable for most cases involving voice control. It receives configuration commands or responds through a serial port interface. With this module, we can control cars or other electrical devices by voice. It can store 15 pieces of voice instruction. Those 15 pieces are divided into 3 groups, with 5 in one group. First, we should record the voice instructions group by group. After that, we should import one group by serial command before it could recognize the 5 voice instructions within that group. If we need to implement instructions in other groups, we should import the group first. This module is speaker-independent. If your friend speaks the voice instruction instead of you, it may not identify the instruction.
SKU: D62 - Arduino Sensor And Modules
MQ9 Carbon Monoxide Methane And LPG Gas Sensor Module in Pakistan
Quick ViewArduino Sensor And ModulesMQ9 Carbon Monoxide Methane And LPG Gas Sensor Module in Pakistan
MQ9 MQ 9 MQ-9 Carbon Monoxide, Methane, and LPG Gas Sensor Module For Arduino can be used to sense Carbon Monoxide and Methane Gas. The sensitive material of the MQ9 MQ 9 MQ-9 gas sensor is SnO2, which with lower conductivity in clean air. It makes detection by method of cycle high and low temperature, and detect CO when low temperature (heated by 1.5V). The sensor’s conductivity is higher along with the gas concentration rising. When the high temperature (heated by 5.0V), detects Methane, Propane, etc. combustible gas and cleans the other gases adsorbed under low temperature.
SKU: D50,B105 - Arduino Sensor And Modules
MQ6 Liquefied Petroleum Isobutane Propane LPG Gas Sensor Module In Pakistan
Quick ViewArduino Sensor And ModulesMQ6 Liquefied Petroleum Isobutane Propane LPG Gas Sensor Module In Pakistan
MQ6 MQ 6 MQ-6 Liquefied Petroleum isobutane-propane gas Sensor Module For Arduino. This sensor has high sensitivity and fast response time. The sensor’s output is an analog resistance. The drive circuit is very simple; all you need to do is power the heater coil with 5V, add a load resistance, and connect the output to an ADC. The sensitive material of the MQ-6 gas sensor is SnO2, which with lower conductivity in clean air. When the target combustible gas exists, The sensor’s conductivity is higher along with the gas concentration rising. Please use a simple electro circuit, Convert the change of conductivity to correspond output signal of gas concentration.MQ-6 gas sensor has a high sensitivity to Propane, Butane, and LPG, also a response to Natural gas. The sensor could be used to detect different combustible gas, especially Methane, which is with low cost and suitable for different applications.
SKU: D53,B105 - Arduino Sensor And Modules
MQ3 Alcohol Ethanol Detector Gas Sensor Module in Pakistan
MQ3 MQ 3 MQ-3 Alcohol Detector Gas Sensor Module is a simple to use MQ-3 Alcohol Detector Gas Sensor Module which can sense the presence of Alcohol in the air. The module uses our MQ-3 sensor. It simplifies the interface to the odd pin spacing of the sensor and provides an interface through standard 4 x 0.1″ header pins. It provides an analog output corresponding to the concentration of the gas in the air and an easy-to-use digital output. The onboard potentiometer can be used to set the maximum gas concentration beyond which the digital output gets triggered. Just power the module with 5V set the threshold and you can start getting the gas concentration of the air around the sensor! An onboard LED signals the presence of any gas. Perfect sensing alcohol concentration on your breath just likes a common breathalyzer. The digital output can be easily interfaced with microcontrollers and other circuits. The analog output can be hooked up to an ADC of a microcontroller to get a wide range of sensor readings.
SKU: D56,B105 - Arduino Sensor And Modules
Fingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
Quick ViewArduino Sensor And ModulesFingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
The GT511C3 GT-511C3 GT 511C3 FPS (fingerprint scanner) is a small embedded module that consists of an optical sensor mounted on a small circuit board. The optical sensor scans a fingerprint and the microcontroller and software provide the functionality of the module which automatically processes the scanned fingerprint. The GT511C3 GT-511C3 GT 511C3 Optical Fingerprint Scanner Module with JST SH Connector is a high-performance fingerprint scanner. This optical sensor module is designed for easy integration into applications with a serial interface (UART). The GT-511C3 is a TTL fingerprint scanner and can be accessed by Raspberry Pi, Arduino, or any other Microcontroller using just two wires viz Tx & Rx.GT-511C3 Fingerprint Scanner module has an onboard optical sensor and a 32-bit CPU. It does most of the heavy work like reading and identifying fingerprints. A simple set of commands has to be sent from your micro-controller and the GT-511C3 fingerprint scanner does the rest of the work. To get started, just register each fingerprint that you want to store by sending the corresponding command and pressing your finger against the reader three times. The fingerprint scanner can store different fingerprints and the database of prints can even be downloaded from the unit and distributed to other modules. As well as the fingerprint “template,” the analyzed version of the print, you can also retrieve the image of a fingerprint and even pull raw images from the optical sensor. We need two wires are for TX and RX and two wires for the power supply (5V). The module can be used in projects for identifying users, for example allowing access through a door by scanning a finger instead of using a key.
SKU: D46
Reviews
There are no reviews yet