- Raspberry Pi & Accessories
- Raspberry Pi Kits
- Raspberry Pi Board
- Raspberry Pi Case
- Raspberry Pi Came
- Raspberry Pi Accessories
This module is a portable mobile power supply that supports 3V,1A, and 5V, 3A two voltage outputs!. 5V voltage output rated current is 2.2A, maximum support 3A current (not recommended for overload, easy to damage the module, speed up the service life), the output of current depends on the quality of the 18650 battery!
Typical usage:
- It is also typically used as a V8 Mobile Power Expansion Board Module.
- Commonly known as Micro USB charger For Arduino ESP32 or ESP8266
- Power source for Arduino ESP8266
MICRO USB charging current 600mA-800mA:
Supports up to two 18650 batteries. It is recommended to use two 18650 batteries, which can be longer!
Special attention: the installation of the battery must be determined positive and negative, the board has been clearly marked positive and negative! Installation errors will burn out the module!
Package Includes:
- 1x 5V UPS Arduino Raspberry Pi Battery Shield in Pakistan
Add a review
You must be logged in to post a review
Log In
Related products
- Arduino Sensor And Modules
Fingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
Quick View
Arduino Sensor And ModulesFingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
The GT511C3 GT-511C3 GT 511C3 FPS (fingerprint scanner) is a small embedded module that consists of an optical sensor mounted on a small circuit board. The optical sensor scans a fingerprint and the microcontroller and software provide the functionality of the module which automatically processes the scanned fingerprint. The GT511C3 GT-511C3 GT 511C3 Optical Fingerprint Scanner Module with JST SH Connector is a high-performance fingerprint scanner. This optical sensor module is designed for easy integration into applications with a serial interface (UART). The GT-511C3 is a TTL fingerprint scanner and can be accessed by Raspberry Pi, Arduino, or any other Microcontroller using just two wires viz Tx & Rx.GT-511C3 Fingerprint Scanner module has an onboard optical sensor and a 32-bit CPU. It does most of the heavy work like reading and identifying fingerprints. A simple set of commands has to be sent from your micro-controller and the GT-511C3 fingerprint scanner does the rest of the work. To get started, just register each fingerprint that you want to store by sending the corresponding command and pressing your finger against the reader three times. The fingerprint scanner can store different fingerprints and the database of prints can even be downloaded from the unit and distributed to other modules. As well as the fingerprint “template,” the analyzed version of the print, you can also retrieve the image of a fingerprint and even pull raw images from the optical sensor. We need two wires are for TX and RX and two wires for the power supply (5V). The module can be used in projects for identifying users, for example allowing access through a door by scanning a finger instead of using a key.
SKU: D46 - Arduino Sensor And Modules
Voice Recognition Module With Microphone Control Voice Board For Arduino in Pakistan
Quick View
Arduino Sensor And ModulesVoice Recognition Module With Microphone Control Voice Board For Arduino in Pakistan
This Voice Recognition Module, which can recognize as many as 15 voice instructions and be suitable for most cases involving voice control. It receives configuration commands or responds through a serial port interface. With this module, we can control cars or other electrical devices by voice. It can store 15 pieces of voice instruction. Those 15 pieces are divided into 3 groups, with 5 in one group. First, we should record the voice instructions group by group. After that, we should import one group by serial command before it could recognize the 5 voice instructions within that group. If we need to implement instructions in other groups, we should import the group first. This module is speaker-independent. If your friend speaks the voice instruction instead of you, it may not identify the instruction.
SKU: D62 - Arduino Sensor And Modules
MQ2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module in Pakistan
Quick View
Arduino Sensor And ModulesMQ2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module in Pakistan
MQ2 MQ-2 MQ 2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module Smoke LPG Butane Hydrogen Gas Sensor Detector Module is useful for gas leakage detection (home and industry). It is suitable for detecting H2, LPG, CH4, CO, Alcohol, Smoke, or Propane. Due to its high sensitivity and fast response time, the measurement can be taken as soon as possible. The sensitivity of the sensor can be adjusted by a potentiometer.MQ-2 gas sensor using gas sensitive material is to be clean air in the lower conductivity of tin oxide (SnO2). When the sensor when flammable gases are present in the environment in which the sensor’s conductivity with increasing concentration of combustible gas in the air increases. Use a simple circuit to convert the changes in conductivity and output signal that corresponds to the concentration of the gas.MQ-2 gas sensor higher sensitivity to liquefied petroleum gas, propane, hydrogen, detection of gas, and other combustible vapors are ideal. This sensor can detect a variety of flammable gas, are a low-cost sensor for many applications.
SKU: D57,B105 - Arduino Sensor And Modules
AD8232 Keyes Single Lead ECG Monitoring Sensor Module In Pakistan
Quick View
Arduino Sensor And ModulesAD8232 Keyes Single Lead ECG Monitoring Sensor Module In Pakistan
The AD8232 Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG or Electrocardiogram and output as an analog reading. ECGs can be extremely noisy, the AD8232 Single Lead Heart Rate Monitor acts as an op-amp to help obtain a clear signal from the PR and QT Intervals easily. The AD8232 is an integrated signal conditioning block for ECG and other bio-potential measurement applications. It is designed to extract, amplify, and filter small bio-potential signals in the presence of noisy conditions, such as those created by motion or remote electrode placement.
SKU: D42,B104 - Arduino Sensor And Modules
MQ4 High Sensitivity Methane Gas (CNG) Detector Sensor Module In Pakistan
Quick View
Arduino Sensor And ModulesMQ4 High Sensitivity Methane Gas (CNG) Detector Sensor Module In Pakistan
MQ4 MQ 4 MQ-4 High Sensitivity Gas Methane (CNG) Detector Sensor Module For Arduino is a simple to use MQ-4 High Sensitivity Gas Methane (CNG) Detector Sensor Module For Arduino which can sense the presence of Compressed Natural Gas(CNG), methane(CH4), etc in the air. The module uses our MQ-4 sensor. It simplifies the interface to the odd pin spacing of the sensor and provides the interface through standard 4 x 0.1″ header pins. It provides an analog output corresponding to the concentration of the gases in the air and an easy-to-use digital output. The onboard potentiometer can be used to set the maximum gas concentration beyond which the digital output gets triggered. Just power the module with 5V set the threshold and you can start getting the gas concentration of the air around the sensor! An onboard LED signals the presence of any gas. The digital output can be easily interfaced to microcontrollers and other circuits. The analog output can be hooked up to an ADC of a microcontroller to get a wide range of sensor readings. This is a simple-to-use compressed natural gas (CNG) sensor, suitable for sensing natural gas (composed of mostly Methane [CH4]) concentrations in the air. The MQ-4 can detect natural gas concentrations anywhere from 200 to 10000ppm.
SKU: D55,B105
Reviews
There are no reviews yet