- Raspberry Pi & Accessories
- Raspberry Pi Kits
- Raspberry Pi Board
- Raspberry Pi Case
- Raspberry Pi Came
- Raspberry Pi Accessories
A basic 16-button keypad for user input. The buttons are set up in a matrix format. This allows a microcontroller to ‘scan’ the 8 output pins to see which of the 16 buttons is being pressed.
- 100% Brand new and high-quality
- Good Quality button
- Expanded development application modules
- 4×4 Matrix
- Keypad Keyboard module 16 Button
- Size: Approx.42mmX42mm / 1.65×1.65
Package Include:
- 1 x 4×4 Matrix Keypad Keyboard Module
Add a review
You must be logged in to post a review
Log In
Related products
- Arduino Sensor And Modules
MQ4 High Sensitivity Methane Gas (CNG) Detector Sensor Module In Pakistan
Quick View
Arduino Sensor And ModulesMQ4 High Sensitivity Methane Gas (CNG) Detector Sensor Module In Pakistan
MQ4 MQ 4 MQ-4 High Sensitivity Gas Methane (CNG) Detector Sensor Module For Arduino is a simple to use MQ-4 High Sensitivity Gas Methane (CNG) Detector Sensor Module For Arduino which can sense the presence of Compressed Natural Gas(CNG), methane(CH4), etc in the air. The module uses our MQ-4 sensor. It simplifies the interface to the odd pin spacing of the sensor and provides the interface through standard 4 x 0.1″ header pins. It provides an analog output corresponding to the concentration of the gases in the air and an easy-to-use digital output. The onboard potentiometer can be used to set the maximum gas concentration beyond which the digital output gets triggered. Just power the module with 5V set the threshold and you can start getting the gas concentration of the air around the sensor! An onboard LED signals the presence of any gas. The digital output can be easily interfaced to microcontrollers and other circuits. The analog output can be hooked up to an ADC of a microcontroller to get a wide range of sensor readings. This is a simple-to-use compressed natural gas (CNG) sensor, suitable for sensing natural gas (composed of mostly Methane [CH4]) concentrations in the air. The MQ-4 can detect natural gas concentrations anywhere from 200 to 10000ppm.
SKU: D55,B105 - Arduino Sensor And Modules
ECG Electrodes with Metal Snap and Low Impedance Solid Medical Conductive Gel In Pakistan
Quick View
Arduino Sensor And ModulesECG Electrodes with Metal Snap and Low Impedance Solid Medical Conductive Gel In Pakistan
ECG Electrodes with Metal Snap and Low Impedance Solid Medical Conductive Gel Disposable ECG electrodes are used for diagnostic ECG or ECG monitoring They can be used for various ECG tests Chunfeng and reg; Disposable ECG electrodes use an AG/AgClsensor element and solid conductive and adhesive Hydro-gel for adhesion The AG/AgCl sensor element has the best sensitivities and the solid conductive and adhesive hydro-gel has very low impedance and is non-irritating, non-sensitizing and non-cytotoxic to the skin All electrodes are latex-free.
SKU: D41,B104 - Arduino Sensor And Modules
MQ135 Air Quality Detector Sensor Module in Pakistan
The MQ135 MQ-135 MQ 135 Air Quality Detector Sensor Module For Arduino has lower conductivity in clean air. When the target combustible gas exists, the conductivity of the sensor is higher along with the gas concentration rising. Convert change of conductivity to the corresponding output signal of gas concentration. The MQ135 MQ-135 MQ 135 gas sensor has a high sensitivity to Ammonia, Sulphide and Benzene steam, also sensitive to smoke and other harmful gases. It is at low cost and suitable for different applications such as harmful gases/smoke detection.
SKU: D49,B105 - Arduino Sensor And Modules
MAX30102 SPO2 Blood Oxygen Pulse Oximeter and Heart Rate Sensor In Pakistan
Quick View
Arduino Sensor And ModulesMAX30102 SPO2 Blood Oxygen Pulse Oximeter and Heart Rate Sensor In Pakistan
The MAX30102 is an integrated pulse oximeter or SO2 sensors, and heart rate monitor biosensor module. MAX30102 SO2 integrates a red LED and an infrared LED, photodetector, optical components, and low-noise electronic circuitry with ambient light suppression.
SKU: D43 - Arduino Sensor And Modules
Fingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
Quick View
Arduino Sensor And ModulesFingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
The GT511C3 GT-511C3 GT 511C3 FPS (fingerprint scanner) is a small embedded module that consists of an optical sensor mounted on a small circuit board. The optical sensor scans a fingerprint and the microcontroller and software provide the functionality of the module which automatically processes the scanned fingerprint. The GT511C3 GT-511C3 GT 511C3 Optical Fingerprint Scanner Module with JST SH Connector is a high-performance fingerprint scanner. This optical sensor module is designed for easy integration into applications with a serial interface (UART). The GT-511C3 is a TTL fingerprint scanner and can be accessed by Raspberry Pi, Arduino, or any other Microcontroller using just two wires viz Tx & Rx.GT-511C3 Fingerprint Scanner module has an onboard optical sensor and a 32-bit CPU. It does most of the heavy work like reading and identifying fingerprints. A simple set of commands has to be sent from your micro-controller and the GT-511C3 fingerprint scanner does the rest of the work. To get started, just register each fingerprint that you want to store by sending the corresponding command and pressing your finger against the reader three times. The fingerprint scanner can store different fingerprints and the database of prints can even be downloaded from the unit and distributed to other modules. As well as the fingerprint “template,” the analyzed version of the print, you can also retrieve the image of a fingerprint and even pull raw images from the optical sensor. We need two wires are for TX and RX and two wires for the power supply (5V). The module can be used in projects for identifying users, for example allowing access through a door by scanning a finger instead of using a key.
SKU: D46
Reviews
There are no reviews yet