- Raspberry Pi & Accessories
- Raspberry Pi Kits
- Raspberry Pi Board
- Raspberry Pi Case
- Raspberry Pi Came
- Raspberry Pi Accessories
The ACS712 30A Range Current Sensor Module / Hall Sensor device consists of a precise, low-offset, linear Hall circuit with a copper conduction path located near the surface of the die. Applied current flowing through this copper conduction path generates a magnetic field which the Hall IC converts into a proportional voltage.
Specifications and Features :
- Module Dimensions: 31 x 13 x 14 mm (LxWxH)
- Weight: 3 gm.
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: -30A~ 30A
- Sensitivity: 66mV/A
- The current sensor chips: ACS712ELC-30B.
- Pin 5V power supply, onboard power indicator.
- The module can be measured plus or minus 30 amps, corresponding to the analog output of 185 mV / A.
- There is no detection current through, the output voltage is VCC / 2.
Package Includes :
- 1 x ACS712 30A Range Current Sensor Module / Hall Sensor.
Add a review
You must be logged in to post a review
Log In
Related products
- Arduino Sensor And Modules
MQ6 Liquefied Petroleum Isobutane Propane LPG Gas Sensor Module In Pakistan
Quick View
Arduino Sensor And ModulesMQ6 Liquefied Petroleum Isobutane Propane LPG Gas Sensor Module In Pakistan
MQ6 MQ 6 MQ-6 Liquefied Petroleum isobutane-propane gas Sensor Module For Arduino. This sensor has high sensitivity and fast response time. The sensor’s output is an analog resistance. The drive circuit is very simple; all you need to do is power the heater coil with 5V, add a load resistance, and connect the output to an ADC. The sensitive material of the MQ-6 gas sensor is SnO2, which with lower conductivity in clean air. When the target combustible gas exists, The sensor’s conductivity is higher along with the gas concentration rising. Please use a simple electro circuit, Convert the change of conductivity to correspond output signal of gas concentration.MQ-6 gas sensor has a high sensitivity to Propane, Butane, and LPG, also a response to Natural gas. The sensor could be used to detect different combustible gas, especially Methane, which is with low cost and suitable for different applications.
SKU: D53,B105 - Arduino Sensor And Modules
MAX30102 SPO2 Blood Oxygen Pulse Oximeter and Heart Rate Sensor In Pakistan
Quick ViewArduino Sensor And ModulesMAX30102 SPO2 Blood Oxygen Pulse Oximeter and Heart Rate Sensor In Pakistan
The MAX30102 is an integrated pulse oximeter or SO2 sensors, and heart rate monitor biosensor module. MAX30102 SO2 integrates a red LED and an infrared LED, photodetector, optical components, and low-noise electronic circuitry with ambient light suppression.
SKU: D43 - Arduino Sensor And Modules
DFPLAYER MINI MP3 PLAYER MODULE FOR ARDUINO UNO MUSIC AUDIO VOICE BOARD
Quick ViewArduino Sensor And ModulesDFPLAYER MINI MP3 PLAYER MODULE FOR ARDUINO UNO MUSIC AUDIO VOICE BOARD
DFPlayer Mini MP3 Player Module is suitable for Arduino UNO Music Audio Voice Board.DFPlayer Mini is a compact and inexpensive MP3 module that can be connected directly to the speaker. Module with battery, speaker, the keyboard can be used alone, or through serial port control, such as the Arduino UNO or any microcontroller with a serial port module. The module itself seamlessly integrated MP3, WAV, WMA hardware decoding. While the software supports TF card drivers to support FAT16, FAT32 file systems. It can be done through simple serial commands specified music player, as well as how to play music and other functions, without the heavy
the underlying operation, easy to use, stable, and reliable.SKU: D59 - Arduino Sensor And Modules
Fingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
Quick ViewArduino Sensor And ModulesFingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
The GT511C3 GT-511C3 GT 511C3 FPS (fingerprint scanner) is a small embedded module that consists of an optical sensor mounted on a small circuit board. The optical sensor scans a fingerprint and the microcontroller and software provide the functionality of the module which automatically processes the scanned fingerprint. The GT511C3 GT-511C3 GT 511C3 Optical Fingerprint Scanner Module with JST SH Connector is a high-performance fingerprint scanner. This optical sensor module is designed for easy integration into applications with a serial interface (UART). The GT-511C3 is a TTL fingerprint scanner and can be accessed by Raspberry Pi, Arduino, or any other Microcontroller using just two wires viz Tx & Rx.GT-511C3 Fingerprint Scanner module has an onboard optical sensor and a 32-bit CPU. It does most of the heavy work like reading and identifying fingerprints. A simple set of commands has to be sent from your micro-controller and the GT-511C3 fingerprint scanner does the rest of the work. To get started, just register each fingerprint that you want to store by sending the corresponding command and pressing your finger against the reader three times. The fingerprint scanner can store different fingerprints and the database of prints can even be downloaded from the unit and distributed to other modules. As well as the fingerprint “template,” the analyzed version of the print, you can also retrieve the image of a fingerprint and even pull raw images from the optical sensor. We need two wires are for TX and RX and two wires for the power supply (5V). The module can be used in projects for identifying users, for example allowing access through a door by scanning a finger instead of using a key.
SKU: D46 - Arduino Sensor And Modules
MQ4 High Sensitivity Methane Gas (CNG) Detector Sensor Module In Pakistan
Quick ViewArduino Sensor And ModulesMQ4 High Sensitivity Methane Gas (CNG) Detector Sensor Module In Pakistan
MQ4 MQ 4 MQ-4 High Sensitivity Gas Methane (CNG) Detector Sensor Module For Arduino is a simple to use MQ-4 High Sensitivity Gas Methane (CNG) Detector Sensor Module For Arduino which can sense the presence of Compressed Natural Gas(CNG), methane(CH4), etc in the air. The module uses our MQ-4 sensor. It simplifies the interface to the odd pin spacing of the sensor and provides the interface through standard 4 x 0.1″ header pins. It provides an analog output corresponding to the concentration of the gases in the air and an easy-to-use digital output. The onboard potentiometer can be used to set the maximum gas concentration beyond which the digital output gets triggered. Just power the module with 5V set the threshold and you can start getting the gas concentration of the air around the sensor! An onboard LED signals the presence of any gas. The digital output can be easily interfaced to microcontrollers and other circuits. The analog output can be hooked up to an ADC of a microcontroller to get a wide range of sensor readings. This is a simple-to-use compressed natural gas (CNG) sensor, suitable for sensing natural gas (composed of mostly Methane [CH4]) concentrations in the air. The MQ-4 can detect natural gas concentrations anywhere from 200 to 10000ppm.
SKU: D55,B105
Reviews
There are no reviews yet