- Raspberry Pi & Accessories
- Raspberry Pi Kits
- Raspberry Pi Board
- Raspberry Pi Case
- Raspberry Pi Came
- Raspberry Pi Accessories
The ACS712 30A Range Current Sensor Module / Hall Sensor device consists of a precise, low-offset, linear Hall circuit with a copper conduction path located near the surface of the die. Applied current flowing through this copper conduction path generates a magnetic field which the Hall IC converts into a proportional voltage.
Specifications and Features :
- Module Dimensions: 31 x 13 x 14 mm (LxWxH)
- Weight: 3 gm.
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: -30A~ 30A
- Sensitivity: 66mV/A
- The current sensor chips: ACS712ELC-30B.
- Pin 5V power supply, onboard power indicator.
- The module can be measured plus or minus 30 amps, corresponding to the analog output of 185 mV / A.
- There is no detection current through, the output voltage is VCC / 2.
Package Includes :
- 1 x ACS712 30A Range Current Sensor Module / Hall Sensor.
Add a review
You must be logged in to post a review
Log In
Related products
- Arduino Sensor And Modules
MQ6 Liquefied Petroleum Isobutane Propane LPG Gas Sensor Module In Pakistan
Quick View
Arduino Sensor And ModulesMQ6 Liquefied Petroleum Isobutane Propane LPG Gas Sensor Module In Pakistan
MQ6 MQ 6 MQ-6 Liquefied Petroleum isobutane-propane gas Sensor Module For Arduino. This sensor has high sensitivity and fast response time. The sensor’s output is an analog resistance. The drive circuit is very simple; all you need to do is power the heater coil with 5V, add a load resistance, and connect the output to an ADC. The sensitive material of the MQ-6 gas sensor is SnO2, which with lower conductivity in clean air. When the target combustible gas exists, The sensor’s conductivity is higher along with the gas concentration rising. Please use a simple electro circuit, Convert the change of conductivity to correspond output signal of gas concentration.MQ-6 gas sensor has a high sensitivity to Propane, Butane, and LPG, also a response to Natural gas. The sensor could be used to detect different combustible gas, especially Methane, which is with low cost and suitable for different applications.
SKU: D53,B105 - Arduino Sensor And Modules
Voice Recognition Module With Microphone Control Voice Board For Arduino in Pakistan
Quick View
Arduino Sensor And ModulesVoice Recognition Module With Microphone Control Voice Board For Arduino in Pakistan
This Voice Recognition Module, which can recognize as many as 15 voice instructions and be suitable for most cases involving voice control. It receives configuration commands or responds through a serial port interface. With this module, we can control cars or other electrical devices by voice. It can store 15 pieces of voice instruction. Those 15 pieces are divided into 3 groups, with 5 in one group. First, we should record the voice instructions group by group. After that, we should import one group by serial command before it could recognize the 5 voice instructions within that group. If we need to implement instructions in other groups, we should import the group first. This module is speaker-independent. If your friend speaks the voice instruction instead of you, it may not identify the instruction.
SKU: D62 - Arduino Sensor And Modules
Fingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
Quick View
Arduino Sensor And ModulesFingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
The GT511C3 GT-511C3 GT 511C3 FPS (fingerprint scanner) is a small embedded module that consists of an optical sensor mounted on a small circuit board. The optical sensor scans a fingerprint and the microcontroller and software provide the functionality of the module which automatically processes the scanned fingerprint. The GT511C3 GT-511C3 GT 511C3 Optical Fingerprint Scanner Module with JST SH Connector is a high-performance fingerprint scanner. This optical sensor module is designed for easy integration into applications with a serial interface (UART). The GT-511C3 is a TTL fingerprint scanner and can be accessed by Raspberry Pi, Arduino, or any other Microcontroller using just two wires viz Tx & Rx.GT-511C3 Fingerprint Scanner module has an onboard optical sensor and a 32-bit CPU. It does most of the heavy work like reading and identifying fingerprints. A simple set of commands has to be sent from your micro-controller and the GT-511C3 fingerprint scanner does the rest of the work. To get started, just register each fingerprint that you want to store by sending the corresponding command and pressing your finger against the reader three times. The fingerprint scanner can store different fingerprints and the database of prints can even be downloaded from the unit and distributed to other modules. As well as the fingerprint “template,” the analyzed version of the print, you can also retrieve the image of a fingerprint and even pull raw images from the optical sensor. We need two wires are for TX and RX and two wires for the power supply (5V). The module can be used in projects for identifying users, for example allowing access through a door by scanning a finger instead of using a key.
SKU: D46 - Arduino Sensor And Modules
MAX9814 Microphone Amplifier Module In Pakistan
The MAX9814 is available in the space-saving, 14-pin TDFN package. This device is specified over the -40°C to +85°C extended temperature range. MAX9814 is a low-cost, high-quality microphone amplifier with automatic gain control (AGC) and low-noise microphone bias. The device features a low-noise preamplifier, variable gain amplifier (VGA), output amplifier, microphone-bias-voltage generator, and AGC control circuitry. The low-noise preamplifier has a fixed 12dB gain, while the VGA gain automatically adjusts from 20dB to 0dB, depending on the output voltage and the AGC threshold. The output amplifier offers selectable gains of 8dB, 18dB, and 28dB. With no compression, the cascade of the amplifiers results in an overall gain of 40dB, 50dB, or 60dB. A trilevel digital input programs the output amplifier gain. An external resistive divider controls the AGC threshold and a single capacitor programs the attack/release times. A trilevel digital input programs the ratio of attack-to-release time. The hold time of the AGC is fixed at 30ms. The low-noise microphone-bias-voltage generator can bias most electret microphones.
SKU: D64,SB47 - Arduino Sensor And Modules
R307 Optical Finger Print Scanner Reader Sensor Module In Pakistan
Quick View
Arduino Sensor And ModulesR307 Optical Finger Print Scanner Reader Sensor Module In Pakistan
R307 R-307 R 307 fingerprint Sensor module For Arduino is a fingerprint sensor with a TTL UART interface. Professional optical technology, precise module manufacturing technic. The good image processing capabilities of Finger Print Reader can successfully capture an image up to resolution 500 dpi Finger detection function. The user can store the fingerprint data in the module and can configure it in 1:1 or 1: N mode for identifying the person. The FP module can directly interface with a 3.3 or 5v Microcontroller. A level converter (like MAX232) is required for interfacing with a PC serial port. R307 Fingerprint Scanner consists of a high-speed DSP processor, high-performance fingerprint alignment algorithm, high-capacity FLASH chips, and other hardware and software composition, stable performance, simple structure, with fingerprint entry, image processing, fingerprint matching, search and template storage, and other functions. The optical fingerprint detection device can be embedded into a variety of end products, such as access control, attendance, safety deposit box, car door locks.
SKU: D47
Reviews
There are no reviews yet