- Raspberry Pi & Accessories
- Raspberry Pi Kits
- Raspberry Pi Board
- Raspberry Pi Case
- Raspberry Pi Came
- Raspberry Pi Accessories
The ACS712 30A Range Current Sensor Module / Hall Sensor device consists of a precise, low-offset, linear Hall circuit with a copper conduction path located near the surface of the die. Applied current flowing through this copper conduction path generates a magnetic field which the Hall IC converts into a proportional voltage.
Specifications and Features :
- Module Dimensions: 31 x 13 x 14 mm (LxWxH)
- Weight: 3 gm.
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: -30A~ 30A
- Sensitivity: 66mV/A
- The current sensor chips: ACS712ELC-30B.
- Pin 5V power supply, onboard power indicator.
- The module can be measured plus or minus 30 amps, corresponding to the analog output of 185 mV / A.
- There is no detection current through, the output voltage is VCC / 2.
Package Includes :
- 1 x ACS712 30A Range Current Sensor Module / Hall Sensor.
Add a review
You must be logged in to post a review
Log In
Related products
- Arduino Sensor And Modules
MQ2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module in Pakistan
Quick View
Arduino Sensor And ModulesMQ2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module in Pakistan
MQ2 MQ-2 MQ 2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module Smoke LPG Butane Hydrogen Gas Sensor Detector Module is useful for gas leakage detection (home and industry). It is suitable for detecting H2, LPG, CH4, CO, Alcohol, Smoke, or Propane. Due to its high sensitivity and fast response time, the measurement can be taken as soon as possible. The sensitivity of the sensor can be adjusted by a potentiometer.MQ-2 gas sensor using gas sensitive material is to be clean air in the lower conductivity of tin oxide (SnO2). When the sensor when flammable gases are present in the environment in which the sensor’s conductivity with increasing concentration of combustible gas in the air increases. Use a simple circuit to convert the changes in conductivity and output signal that corresponds to the concentration of the gas.MQ-2 gas sensor higher sensitivity to liquefied petroleum gas, propane, hydrogen, detection of gas, and other combustible vapors are ideal. This sensor can detect a variety of flammable gas, are a low-cost sensor for many applications.
SKU: D57,B105 - Arduino Sensor And Modules
AD8232 Keyes Single Lead ECG Monitoring Sensor Module In Pakistan
Quick View
Arduino Sensor And ModulesAD8232 Keyes Single Lead ECG Monitoring Sensor Module In Pakistan
The AD8232 Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG or Electrocardiogram and output as an analog reading. ECGs can be extremely noisy, the AD8232 Single Lead Heart Rate Monitor acts as an op-amp to help obtain a clear signal from the PR and QT Intervals easily. The AD8232 is an integrated signal conditioning block for ECG and other bio-potential measurement applications. It is designed to extract, amplify, and filter small bio-potential signals in the presence of noisy conditions, such as those created by motion or remote electrode placement.
SKU: D42,B104 - Arduino Sensor And Modules
MQ4 High Sensitivity Methane Gas (CNG) Detector Sensor Module In Pakistan
Quick View
Arduino Sensor And ModulesMQ4 High Sensitivity Methane Gas (CNG) Detector Sensor Module In Pakistan
MQ4 MQ 4 MQ-4 High Sensitivity Gas Methane (CNG) Detector Sensor Module For Arduino is a simple to use MQ-4 High Sensitivity Gas Methane (CNG) Detector Sensor Module For Arduino which can sense the presence of Compressed Natural Gas(CNG), methane(CH4), etc in the air. The module uses our MQ-4 sensor. It simplifies the interface to the odd pin spacing of the sensor and provides the interface through standard 4 x 0.1″ header pins. It provides an analog output corresponding to the concentration of the gases in the air and an easy-to-use digital output. The onboard potentiometer can be used to set the maximum gas concentration beyond which the digital output gets triggered. Just power the module with 5V set the threshold and you can start getting the gas concentration of the air around the sensor! An onboard LED signals the presence of any gas. The digital output can be easily interfaced to microcontrollers and other circuits. The analog output can be hooked up to an ADC of a microcontroller to get a wide range of sensor readings. This is a simple-to-use compressed natural gas (CNG) sensor, suitable for sensing natural gas (composed of mostly Methane [CH4]) concentrations in the air. The MQ-4 can detect natural gas concentrations anywhere from 200 to 10000ppm.
SKU: D55,B105 - Arduino Sensor And Modules
WTV020SD-16P music module Mp3 Module For Arduino in Pakistan
The WTV020SD is a small, simple IC for embedding audio playback into your next project. These devices are commonly used in children’s toys and talking retail displays. This breakout board allows you to access the functionality of the WTV020SD to give a voice to your next project. The breakout board includes a battery connector and a micro-SD card slot. Simply load your audio files onto a micro-SD card and plug it in, power up the module, and trigger the playback. Playback can be triggered in either key or serial mode: The key-mode provides a stand-alone operation where a host micro is not required. With only 3 push buttons, a 3V battery, and a speaker, an extremely compact and low component count MP3-Player-like system can be implemented. The serial mode provides a simple, 2-wire interface to any micro-controller via its DATA and CLK lines. Audio operations such as PLAY, PAUSE, STOP, and VOLUME control functions are all available to the host micro via simple serial commands. The audio compression used in this module is a little strange (4-bit ADPCM @ 6-32kHz) so you’ll need to download the utility in the documents below in order to convert yours. WAV files into the 4-bit ADPCM format required.
SKU: D60 - Arduino Sensor And Modules
Fingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
Quick View
Arduino Sensor And ModulesFingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
The GT511C3 GT-511C3 GT 511C3 FPS (fingerprint scanner) is a small embedded module that consists of an optical sensor mounted on a small circuit board. The optical sensor scans a fingerprint and the microcontroller and software provide the functionality of the module which automatically processes the scanned fingerprint. The GT511C3 GT-511C3 GT 511C3 Optical Fingerprint Scanner Module with JST SH Connector is a high-performance fingerprint scanner. This optical sensor module is designed for easy integration into applications with a serial interface (UART). The GT-511C3 is a TTL fingerprint scanner and can be accessed by Raspberry Pi, Arduino, or any other Microcontroller using just two wires viz Tx & Rx.GT-511C3 Fingerprint Scanner module has an onboard optical sensor and a 32-bit CPU. It does most of the heavy work like reading and identifying fingerprints. A simple set of commands has to be sent from your micro-controller and the GT-511C3 fingerprint scanner does the rest of the work. To get started, just register each fingerprint that you want to store by sending the corresponding command and pressing your finger against the reader three times. The fingerprint scanner can store different fingerprints and the database of prints can even be downloaded from the unit and distributed to other modules. As well as the fingerprint “template,” the analyzed version of the print, you can also retrieve the image of a fingerprint and even pull raw images from the optical sensor. We need two wires are for TX and RX and two wires for the power supply (5V). The module can be used in projects for identifying users, for example allowing access through a door by scanning a finger instead of using a key.
SKU: D46
Reviews
There are no reviews yet