- Raspberry Pi & Accessories
- Raspberry Pi Kits
- Raspberry Pi Board
- Raspberry Pi Case
- Raspberry Pi Came
- Raspberry Pi Accessories
The ACS712 30A Range Current Sensor Module / Hall Sensor device consists of a precise, low-offset, linear Hall circuit with a copper conduction path located near the surface of the die. Applied current flowing through this copper conduction path generates a magnetic field which the Hall IC converts into a proportional voltage.
Specifications and Features :
- Module Dimensions: 31 x 13 x 14 mm (LxWxH)
- Weight: 3 gm.
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: -30A~ 30A
- Sensitivity: 66mV/A
- The current sensor chips: ACS712ELC-30B.
- Pin 5V power supply, onboard power indicator.
- The module can be measured plus or minus 30 amps, corresponding to the analog output of 185 mV / A.
- There is no detection current through, the output voltage is VCC / 2.
Package Includes :
- 1 x ACS712 30A Range Current Sensor Module / Hall Sensor.
Based on 0 reviews
Be the first to review “30A range Current Sensor Module ACS712 in Pakistan”
Related products
- Arduino Sensor And Modules
MQ4 High Sensitivity Methane Gas (CNG) Detector Sensor Module In Pakistan
Quick View
Arduino Sensor And ModulesMQ4 High Sensitivity Methane Gas (CNG) Detector Sensor Module In Pakistan
MQ4 MQ 4 MQ-4 High Sensitivity Gas Methane (CNG) Detector Sensor Module For Arduino is a simple to use MQ-4 High Sensitivity Gas Methane (CNG) Detector Sensor Module For Arduino which can sense the presence of Compressed Natural Gas(CNG), methane(CH4), etc in the air. The module uses our MQ-4 sensor. It simplifies the interface to the odd pin spacing of the sensor and provides the interface through standard 4 x 0.1″ header pins. It provides an analog output corresponding to the concentration of the gases in the air and an easy-to-use digital output. The onboard potentiometer can be used to set the maximum gas concentration beyond which the digital output gets triggered. Just power the module with 5V set the threshold and you can start getting the gas concentration of the air around the sensor! An onboard LED signals the presence of any gas. The digital output can be easily interfaced to microcontrollers and other circuits. The analog output can be hooked up to an ADC of a microcontroller to get a wide range of sensor readings. This is a simple-to-use compressed natural gas (CNG) sensor, suitable for sensing natural gas (composed of mostly Methane [CH4]) concentrations in the air. The MQ-4 can detect natural gas concentrations anywhere from 200 to 10000ppm.
SKU: D55,B105 - Arduino Sensor And Modules
MQ7 CO Carbon Monoxide Coal Gas Sensor Module In Pakistan
MQ7 MQ 7 MQ-7 CO Carbon Monoxide Coal Gas Sensor Module For Arduino detects the concentrations of CO in the air and outputs its reading as an analog voltage. The sensor can measure concentrations of 10 to 10,000 ppm. The sensor can operate at temperatures from -10 to 50°C and consumes less than 150 mA at 5 V.This module provides both digital and analog outputs. The threshold level for digital output can be easily adjusted using the preset on the board. The MQ-7 sensor module can be easily interfaced with microcontrollers, Arduino, etc.
SKU: D52,B105 - Arduino Sensor And Modules
Fingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
Quick ViewArduino Sensor And ModulesFingerprint Scanner GT-511C3 Bio-Metric Sensor Module In Pakistan
The GT511C3 GT-511C3 GT 511C3 FPS (fingerprint scanner) is a small embedded module that consists of an optical sensor mounted on a small circuit board. The optical sensor scans a fingerprint and the microcontroller and software provide the functionality of the module which automatically processes the scanned fingerprint. The GT511C3 GT-511C3 GT 511C3 Optical Fingerprint Scanner Module with JST SH Connector is a high-performance fingerprint scanner. This optical sensor module is designed for easy integration into applications with a serial interface (UART). The GT-511C3 is a TTL fingerprint scanner and can be accessed by Raspberry Pi, Arduino, or any other Microcontroller using just two wires viz Tx & Rx.GT-511C3 Fingerprint Scanner module has an onboard optical sensor and a 32-bit CPU. It does most of the heavy work like reading and identifying fingerprints. A simple set of commands has to be sent from your micro-controller and the GT-511C3 fingerprint scanner does the rest of the work. To get started, just register each fingerprint that you want to store by sending the corresponding command and pressing your finger against the reader three times. The fingerprint scanner can store different fingerprints and the database of prints can even be downloaded from the unit and distributed to other modules. As well as the fingerprint “template,” the analyzed version of the print, you can also retrieve the image of a fingerprint and even pull raw images from the optical sensor. We need two wires are for TX and RX and two wires for the power supply (5V). The module can be used in projects for identifying users, for example allowing access through a door by scanning a finger instead of using a key.
SKU: D46 - Arduino Sensor And Modules
MP3 Music Player UART Control Serial Module In Pakistan
YX5300 UART Control Serial MP3 Music Player Module For Arduino/AVR/ARM/PIC. The module is a kind of simple MP3 player device which is based on a high-quality MP3 audio chip—YX5300. It can support 8k Hz~ 48k Hz sampling frequency MP3 and WAV file formats. There is a TF card socket on board, so you can plug the micro SD card that stores audio files. MCU can control the MP3 playback state by sending commands to the module via the UART port, such as switch songs, change the volume and play mode, and so on. You can also debug the module via USB to the UART module. It is compatible with Arduino/AVR/ARM/PIC.
SKU: D61 - Arduino Sensor And Modules
EMG Muscle Sensor Module for Arduino in Pakistan
This Muscle Sensor Module for Arduino Specially Designed For Microcontrollers will measure the filtered and rectified electrical activity of a muscle, depending on the amount of activity in the selected muscle. By detecting the electromyogram (EMG), measuring muscle activity has traditionally been used in medical research, however with shrinking but more powerful microcontrollers and integrated circuits advent EMG power Road and sensors can be used for various control systems. The sensor will measure the electrical activity of the muscle output 0-Vs volts, the output size to take Depending on the amount of muscle activity is selected.
SKU: D40
There are no reviews yet.