- Raspberry Pi & Accessories
- Raspberry Pi Kits
- Raspberry Pi Board
- Raspberry Pi Case
- Raspberry Pi Came
- Raspberry Pi Accessories
This module is a portable mobile power supply that supports 3V,1A, and 5V, 3A two voltage outputs!. 5V voltage output rated current is 2.2A, maximum support 3A current (not recommended for overload, easy to damage the module, speed up the service life), the output of current depends on the quality of the 18650 battery!
Typical usage:
- It is also typically used as a V8 Mobile Power Expansion Board Module.
- Commonly known as Micro USB charger For Arduino ESP32 or ESP8266
- Power source for Arduino ESP8266
MICRO USB charging current 600mA-800mA:
Supports up to two 18650 batteries. It is recommended to use two 18650 batteries, which can be longer!
Special attention: the installation of the battery must be determined positive and negative, the board has been clearly marked positive and negative! Installation errors will burn out the module!
Package Includes:
- 1x 5V UPS Arduino Raspberry Pi Battery Shield in Pakistan
Add a review
You must be logged in to post a review
Log In
Related products
- Arduino Sensor And Modules
AD8232 Keyes Single Lead ECG Monitoring Sensor Module In Pakistan
Quick View
Arduino Sensor And ModulesAD8232 Keyes Single Lead ECG Monitoring Sensor Module In Pakistan
The AD8232 Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG or Electrocardiogram and output as an analog reading. ECGs can be extremely noisy, the AD8232 Single Lead Heart Rate Monitor acts as an op-amp to help obtain a clear signal from the PR and QT Intervals easily. The AD8232 is an integrated signal conditioning block for ECG and other bio-potential measurement applications. It is designed to extract, amplify, and filter small bio-potential signals in the presence of noisy conditions, such as those created by motion or remote electrode placement.
SKU: D42,B104 - Arduino Sensor And Modules
Pulse Sensor Pulse Heart Rate Sensor Module In Pakistan
Arduino heartbeat sensor or heart rate data can be used in many Electronic design and microcontroller projects. But the heart rate data is difficult to read, however, the Pulse Sensor Amped helps us to read heart rate. The Heart Beat Pulse Sensor Amped is a plug-and-play heart-rate sensor for Arduino. It can be used by students, artists, athletes, makers, and game & mobile developers who want to easily incorporate live heart-rate data into their projects.
SKU: D45 - Arduino Sensor And Modules
MQ2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module in Pakistan
Quick ViewArduino Sensor And ModulesMQ2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module in Pakistan
MQ2 MQ-2 MQ 2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module Smoke LPG Butane Hydrogen Gas Sensor Detector Module is useful for gas leakage detection (home and industry). It is suitable for detecting H2, LPG, CH4, CO, Alcohol, Smoke, or Propane. Due to its high sensitivity and fast response time, the measurement can be taken as soon as possible. The sensitivity of the sensor can be adjusted by a potentiometer.MQ-2 gas sensor using gas sensitive material is to be clean air in the lower conductivity of tin oxide (SnO2). When the sensor when flammable gases are present in the environment in which the sensor’s conductivity with increasing concentration of combustible gas in the air increases. Use a simple circuit to convert the changes in conductivity and output signal that corresponds to the concentration of the gas.MQ-2 gas sensor higher sensitivity to liquefied petroleum gas, propane, hydrogen, detection of gas, and other combustible vapors are ideal. This sensor can detect a variety of flammable gas, are a low-cost sensor for many applications.
SKU: D57,B105 - Arduino Sensor And Modules
MP3 Music Player UART Control Serial Module In Pakistan
YX5300 UART Control Serial MP3 Music Player Module For Arduino/AVR/ARM/PIC. The module is a kind of simple MP3 player device which is based on a high-quality MP3 audio chip—YX5300. It can support 8k Hz~ 48k Hz sampling frequency MP3 and WAV file formats. There is a TF card socket on board, so you can plug the micro SD card that stores audio files. MCU can control the MP3 playback state by sending commands to the module via the UART port, such as switch songs, change the volume and play mode, and so on. You can also debug the module via USB to the UART module. It is compatible with Arduino/AVR/ARM/PIC.
SKU: D61 - Arduino Sensor And Modules
WTV020SD-16P music module Mp3 Module For Arduino in Pakistan
The WTV020SD is a small, simple IC for embedding audio playback into your next project. These devices are commonly used in children’s toys and talking retail displays. This breakout board allows you to access the functionality of the WTV020SD to give a voice to your next project. The breakout board includes a battery connector and a micro-SD card slot. Simply load your audio files onto a micro-SD card and plug it in, power up the module, and trigger the playback. Playback can be triggered in either key or serial mode: The key-mode provides a stand-alone operation where a host micro is not required. With only 3 push buttons, a 3V battery, and a speaker, an extremely compact and low component count MP3-Player-like system can be implemented. The serial mode provides a simple, 2-wire interface to any micro-controller via its DATA and CLK lines. Audio operations such as PLAY, PAUSE, STOP, and VOLUME control functions are all available to the host micro via simple serial commands. The audio compression used in this module is a little strange (4-bit ADPCM @ 6-32kHz) so you’ll need to download the utility in the documents below in order to convert yours. WAV files into the 4-bit ADPCM format required.
SKU: D60
Reviews
There are no reviews yet