Dark Light

MACH3 USB CNC Interface Board BL-UsbMach-V2.0 MACH3 CNC Board In Pakistan

5-Axis 100KHz USB CNC Controller Card for Mach3 lets you use any Windows Computer to be used as CNC Machine Controller. Previously with LPT Port-Based Cards, the user was limited to use only older computers that had LPT Port. With this New CNC Control Board, you can even run Mach3 on a Windows Tablet which can give a more compact and professional look to your CNC Machine.

Compare
Availability:

Out of stock

5,300

Out of stock

5-Axis 100KHz USB CNC Controller Card for Mach3 lets you use any Windows Computer to be used as CNC Machine Controller. Previously with LPT Port-Based Cards, the user was limited to use only older computers that had LPT Port. With this New CNC Control Board, you can even run Mach3 on a Windows Tablet which can give a more compact and professional look to your CNC Machine.

Technical Specifications

  1. PWM output is available ( ( photocoupler separated,5V)  and can be used to control the spindle speed controller that is controlled by PWM.
  2. Four output ports are available which can be connected to relay modules with photocouplers, to control flood and mist, etc. Mach3 USB interface board BL-UsbMACH-V20 manual
  3.  It can be connected to stepper motor drivers using a common anode or common cathode input connection. Note: stepper motor drivers should have photocouplers for input.
  4. Also, provide 5 axis XH2.54-4P 2.54mm Socket Connector making it easy to connect to the stepper motor drivers. stepper motor drivers.
  5. All the port names are printed on board, Easy to be used

Specifications:

  1. Part Number: BL-USBMach V2.0
  2. No of Axis: 5  (you can connect 5 stepper motor drives or servo drives)
  3. Maximum step-pulse frequency: 100KHz  (suitable for smooth servo or stepper motion)
  4. Automatic probe tool Support: Yes
  5. Emergency input: Yes
  6. Limit switches: Yes (5 general-purpose inputs, you can connect the limit switch, estop switch, probe switch, back to zero, and other devices)
  7. Electronic handwheel Support: Yes
  8. Optical Isolation between USB Side Control and External inputs: Yes
  9. External Voltage: 12V/24V
  10. Spindle Control Output: Yes (0-10V output port) with Spindle Direction (FWD) output
  11. Isolated Outputs: 4 general-purpose isolated relay drive output interfaces (can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps, and another device)
  12. Power Status LED: 1 Status LED (indicate Power status of the controller board)
  13. Size: 9x6cm / 3.54×2.36in
  14. Tested with the following Operating Systems:
    1. Windows XP (direct)
    2. Windows 7 64bit /32Bit (direct)
    3. Windows 10 (Indirect using Windows XP on VMWare)

Setup Instructions

  1. Step 1: Install Mach3: If you already have a Mach3 Installed, skip this step.
  2. Step 2: Download the USB Motion Driver BL-UsbMach-V22.dll and copy and paste the file into your Mach3 Plugins folder Example: “C:/Users/ProgramFiles/Mach3/Plugins”
  3. Step 3: Make sure your board is connected to the PC via a USB cable. It should automatically recognize the USB device.
  4. Step 4: Open Mach3 and you should be prompted to select a driver. Select the “USBMach V2.0” and check “Don’t ask me again”. This will allow your board to communicate with Mach3.
  5. Step 5: Download the XML Mach3 Config File above by right-clicking on the link and selecting “save as”. Save the Mach3Mill.xml file in your Mach3 root folder.

 

 

MACH3 USB CNC Interface Board BL-UsbMach-V2.0 MACH3 CNC Board In Pakistan

 

 

 

MACH3 USB CNC Interface Board BL-UsbMach-V2.0 MACH3 CNC Board In Pakistan

 

 

 

MACH3 USB CNC Interface Board BL-UsbMach-V2.0 MACH3 CNC Board In Pakistan

 

 

 

MACH3 USB CNC Interface Board BL-UsbMach-V2.0 MACH3 CNC Board In Pakistan

 

 

 

MACH3 USB CNC Interface Board BL-UsbMach-V2.0 MACH3 CNC Board In Pakistan

 

 

MACH3 USB CNC Interface Board BL-UsbMach-V2.0 MACH3 CNC Board In Pakistan

MACH3 USB CNC Interface Board BL-UsbMach-V2.0 MACH3 CNC Board In Pakistan

 

Package Includes

  1. 1x 5-Axis 100KHz USB CNC Controller Card for Mach3 – BL-USBMACH V2.0 (QC-OK/Tested)
SKU: D2487 Category:

Reviews

There are no reviews yet

Add a review
You must be logged in to post a review Log In

SHOPPING CART

close
error: Content is protected !!
X